Bandana Dress Tutorial + Bonus Project

If this is your first time visiting my blog - Welcome!  I hope you enjoyed my segment on Good Day Wisconsin this morning and have ventured here to get the details so you can make your girlies these super cute bandana dresses.  And how about how thrifty?!?!  A mere $7 if you don't use the 40% off coupon that Hobby Lobby has online.

As far as tutorials go, I'm still getting my feet wet with how to present them.  So if I'm not clear in an area or you're still confused on something, let me know and I can try to explain it better.  I would rate this as an INTERMEDIATE project, because while it's mostly straight seams, the ruffle is a little tricky.

Here's what you need for materials:
-Scissors
-Sewing Machine
-Thread
-4 bandanas
-Coordinating Ribbon
-Ruler
-Pencil
-Tape
-Matches or Fray Check
-Iron

Here goes!

P.s.  RST = Right Sides Together, RSO = Right Sides Out,  WST = Wrong Sides Together, WSO = Wrong Sides Out

The first thing is to create a pocket for the ribbon to thread through at the end.

Fold over 1 1/2" with WST and stitch a straight seam.  Do this on both red bandanas. 

 

Next, put both red bandanas {with pockets sewn} RST.  Measure down 6 1/2" from the ribbon pocket down the side and pin at that point to mark it.  Sew a straight seam from the pin down the side, away from the ribbon pocket.  Those will be the arm "holes" later.

You can see here the side seam and the top of the dress folded open.  It is inside out at this point.

 Now take the blue and white bandanas and cut 3 - 6" strips out of each of them.

{Note: if there is writing on the bandana, cut that off and do not use it.  There will be extra bandana material left after you cut the strips.}

 

Next, take the blue strips and sew the strips RST, end-to-end to make one long strip of blue.  Then do the same with the white strips.  Iron.

After that you will stack the long white strip on top of the long blue strip RST, and straight stitch the entire length.  When done, you'll have a long rectangle that's white on top and blue on the bottom.

{unfortunately, I didn't photograph this very well.  If you look at the finished dress, it'll make sense.}

Ok, so if there's a "tricky" part to this dress, this next part is it.  It's going to sound more complicated than it really is, so don't over-think it!  I would also suggest practicing on one of those scraps I mentioned earlier.

Keep your sewing machine set to a straight stitch, but increase the LENGTH of the stitch to as long as it will go.  Mine is a dial that ranges from 1-4 and I set mine to "4" for this.

Now we'll do the gathering stitch.  

Straight stitch along the length of the WHITE side of your white & blue rectangle.  It'll be a long stitch, but it goes fast with the stitch lengthened!  Straight stitch about 1/2" in from the edge.  

{Leave longer lengths of thread coming out from both ends of the stitch when done!!}

This is my practice piece.

 Before we actually gather the fabric, take the time to do a hem on the blue side now.  Fold the blue WST about 1/2" and do a straight stitch along the length of the blue side.  You will now have done a stitch down both lengths of that long strip of fabric.  One will be a finished edge, the other your gathering stitch.

Now we can make that cute ruffled gather!  Grasping both of the trailing threads on one end, pull gently on one at a time.  Only one will actually cause the fabric to gather.  Hold it taut and gently slide the fabric down the thread towards the other side.  

This is my practice one below.  When you gather the actual skirting, you will want to gather from each side, towards the middle.  It'll make it a lot easier!  And keep in mind that the gather does not have to be super tight on this dress.  Just a loose gather is fine.

 

 Now fold the gathered skirting's short ends RST and stitch to make the loop of skirting.  Again, look at the finished product, or my pictures below for clarification.

You can see above the hem stitch on the bottom, the gather on top and the side seam to join it into a loop.

  Now, lay the red bandana top RSO on a flat surface and slide the skirting piece WSO over the top.  It'll look like this.  {sort of like if your skirt blew up in the wind}

 

Work your way around that seam pinning as you go and adjusting the gathering so it's even all the way around.

Once you have it pinned all the way around, stitch around the waist seam you just pinned to attach the skirting to the red bandana top.  Remove pins as you go.  You will be able to futz with the gathering while sewing too.  Just take it slow.

Flip the skirting down and iron.

Now for the ribbon shoulder ties.  Cut 2 pieces of ribbon that are 1 1/2 times the width of the top ribbon pocket.  Singe the edges with a match to prevent fraying, or use Fray Check.

 

Take one end of the ribbon and tape it over the end of a pencil like this.

 

 Simply thread it through the pocket at the top of the dress.  Do this through both pockets.

 

You're done!  Have your sweet girlie step into the dress and tie the ends of the ribbon together over each shoulder.  VOILA!

  

HINT:  Be sure to tie the ribbons when washing so they stay put!

And get creative and even more thrifty.  Look for vintage bandanas and scarves at thrift stores and rummage sales to make into dresses and tops.  To make a cutesie halter top, just leave off the skirting and adjust the length of the bandana to how long you want the top to be.

Remember that BONUS  project I told you about?  How about using your scraps to make this: